Hellcat Pro Magwell to Barrel: What Fits the Hellcat, Pro and OSP

13 min read

Search for a hellcat pro magwell and you land on a category page that lists parts for the whole Hellcat family without telling you which of them fit the gun in your safe. Springfield Armory currently sells the Hellcat in two frame lengths — a 3" Micro-Compact and a 3.7" Pro — and every current model of both is an OSP optics-ready configuration. Some parts cross that 3"/3.7" line. Several do not, and the ones that do not are the expensive ones.

Every fitment claim below is taken either from a Springfield Armory spec sheet or from the NDZ Performance product listing for the part itself, both read on September 4, 2026, with the Springfield spec tables re-checked on September 9, 2026. Where a listing does not state fitment, this page says Not confirmed rather than guessing. Frames differ between these two guns, so a part fitting one is not evidence it fits the other.

NDZ for Springfield Hellcat & Hellcat Pro Magazine Release, shown for the Hellcat, Hellcat Pro and OSP fitment guide.

OSP is a configuration, not a third gun

This is the first thing a fitment chart gets wrong. Springfield’s current model list for the 3" Hellcat shows every variant carrying an OSP designation — HC9319BOSP in black, HC9319FOSP in Desert FDE, HC931380BOSP in .380 ACP. The Hellcat Pro list reads the same way: HCP9379BOSP, HCP9379BOSP-15, HCP9379BOSP-COMP for the compensated model, HCP9449BTOSP for the threaded one. Springfield describes the Pro as "an OSP configuration designed to accept today’s most popular micro red dots," and describes the 3" gun’s rear slide deck as cut to accept a micro red dot.

So when you are offered Hellcat, Hellcat Pro and Hellcat OSP as three fitment choices, treat the third as a slide feature rather than a separate frame. For anything that bolts to the frame — magazine release, trigger, pins, grip — OSP is irrelevant. For anything that sits on the slide — optic adapter plate, rear cover plate, slide racker plate — OSP is the entire point, because the optics cut is what those parts index to.

The two frames, side by side

SpecHellcat 3" Micro-Compact OSP (HC9319BOSP)Hellcat Pro OSP (HCP9379BOSP)Hellcat Pro Comp OSP (HCP9379BOSP-COMP)
Barrel3" hammer forged, 1:103.7" hammer forged, 1:103.7" hammer forged, 1:10
SlideBillet machined, optics readyBillet machined, optics readyBillet machined, optics ready, integral compensator
Overall length6"6.6"6.6"
Height4" flush / 4.5" extended4.8" flush / 5.3" extended4.8" flush / 5.3" extended
Weight17.9 oz / 18.3 oz extended21 oz / 21.4 oz extended21 oz / 21.4 oz extended
Grip width1"1"1"
Magazines shipped(1) 11-rd, (1) 13-rd extended(1) 15-rd, (1) 17-rd(1) 15-rd, (1) 17-rd
Recoil systemDual captive spring, full-length guide rodDual captive spring, full-length guide rodDual captive spring, full-length guide rod
Springfield Armory spec tables for the standard retail HC9319BOSP, HCP9379BOSP and HCP9379BOSP-COMP, read September 9, 2026. Magazine counts are the one row that moves with the part number rather than the model: the Pro page is headlined "TWO MAGAZINES INCLUDED," while HCP9379BOSP-15 ships (2) 15-Round and the low-capacity HCP9379BOSPLC ships (2) 10-Round. Read the spec table for the exact SKU you are buying.

Read those two columns together and the fitment pattern makes sense. Grip width is the same 1" on both guns. Height and overall length are not. Anything that wraps the grip or caps the magazine has to match the length of the frame it sits on, which is why the sleeve-and-magwell class of parts is the first place fitment breaks, while a magazine release button — a small part in the same relative position on both frames — crosses without trouble.

The Hellcat Pro magwell question, answered directly

A search of the NDZ catalog on September 4, 2026 for "hellcat magwell" returned zero products. That same search box returned 41 products for "magwell" on its own and 49 for "hellcat" on its own, so the zero is a real result and not a broken query. NDZ does list magwells for other platforms — a Springfield Echelon Lo-Pro Magwell and a Glock 43X/48 magwell are both in the catalog — so what is missing is a Hellcat-specific one, not the part type.

The Echelon listing is worth reading if you want to understand why. NDZ sells that magwell in three frame sizes and states it fits all sizes of stock backstrap. A magwell is keyed to the dimensions of one specific frame. Even if a Hellcat Pro magwell shows up later, it would not be the same part as a 3" Hellcat magwell, and it is not a part to expect to share between the two guns. Do not buy a magwell listed for "Hellcat" and assume it drops onto a Pro.

If the real goal is a faster reload and a fuller firing grip rather than the funnel itself, two parts NDZ does list address that job. The NDZ for Springfield Hellcat and Hellcat Pro magazine release comes in Standard, Plus and Extended protrusion so you can reach the button without breaking grip, and on the short gun the finger-extension base plates recover the pinky that a flush magazine costs you. Magazine and extension fitment is covered in detail in the Hellcat Pro magazines and extensions guide.

Fitment table: what fits which Hellcat

Part typeFits 3" HellcatFits Hellcat ProFits OSP modelsNDZ part
MagwellNone listedNone listedN/ANo Hellcat or Hellcat Pro magwell returned by catalog search on 2026-09-04
Magazine releaseYesYesFrame part — OSP does not affect itHCT9-MR-V, listed for Hellcat, Hellcat Pro, Hellcat Pro Comp, Hellcat RDP and Hellcat .380
Grip sleeveYesNot confirmedFrame part — OSP does not affect itHogue Handall Beavertail HGU-18310, listed "For Gun Model: Hellcat" only
Magazine base plateYes, by magazine capacity15-rd magazine onlyMagazine part — OSP does not affect itHCT9-MP15-V (15-rd) listed for Hellcat, Hellcat Pro and Hellcat Pro Comp; HCT9-MP10-V is listed "For Gun Model: Hellcat" only, so a Pro shipped with 10-rd magazines has no NDZ plate listed
Optic adapter plateYesYesYes — this is the part the OSP cut exists forHCT9-AP1-BLK, listed for Hellcat, Hellcat Pro and Hellcat Pro Comp; mounts Holosun 407K, 507K or EPS Carry
Rear slide cover plateYesYesYesHCT9-RP-V, listed for Hellcat, Hellcat Pro, Hellcat Pro Comp and Hellcat .380
Slide racker plateYesYesYesHCT9-SRP-V1-V, listed for Hellcat Standard, Hellcat Pro, Hellcat Pro Comp and Hellcat RDP
Barrel3" part only3.7" part onlySlide-length dependent, not OSP dependentNDZ-BRL-HCT9-T-V is 3"; NDZ-BRL-HCT9PR-V is 3.7" and states "Does Not Fit: Hellcat 3", Hellcat RDP Models"
Recoil springHellcat spring onlyPro spring onlyFrame/slide part — OSP does not affect itISMI-RS-HCTG3C-V states "Does Not Fit: Hellcat Pro – 3.7""; ISMI-RS-SPG-HCTPR-V states "Does Not Fit: Original Hellcat"
Guide rod assemblyYes, Hellcat variantYes, Hellcat Pro variantFrame part — OSP does not affect itNDZ-GRA-SPG-HCTPR-V — one listing, two variants; the listing tells you to choose the correct one
Trigger kitYesYesFrame part — OSP does not affect itApex ATS-115-112, listed for Hellcat, Hellcat Pro and Hellcat Pro Comp
Pin kitYesYesFrame part — OSP does not affect itNDZ-SPG-HCT9-PIN-123-V, listed for Hellcat, Hellcat Pro, Hellcat Pro Comp and Hellcat RDP
Sourced from the NDZ product listing for each part and from Springfield Armory spec sheets, read September 4, 2026. Confirm fitment on the product page before ordering.

What genuinely crosses both frames

Seven part groups are listed by NDZ as fitting the short Hellcat and the Pro from the same part number. They fall into three categories.

  • Slide deck parts. The NDZ RMSc adapter plate is listed for Hellcat, Hellcat Pro and Hellcat Pro Comp and lets you run a Holosun 407K, 507K or EPS Carry using the screws that ship with the optic. The rear slide cover plate covers the same three plus the Hellcat .380. The slide racker plate adds the RDP. One optics cut across the family is why a single plate covers all of them.
  • Small frame hardware. The magazine release is listed for every Hellcat model NDZ names, including the .380. The Apex trigger enhancement kit covers Hellcat, Hellcat Pro and Hellcat Pro Comp. The stainless pin kit covers those three plus the RDP. None of these depend on the length of the frame or the slide.
  • Magazine hardware. The 15-round magazine base plate, HCT9-MP15-V, is listed for Hellcat, Hellcat Pro and Hellcat Pro Comp under one part number, so it does cross both guns. Capacity is not the whole story, though — the same listing rules out 10 and 13 round magazines, and the 10-round plate, HCT9-MP10-V, is listed "For Gun Model: Hellcat" with no mention of the Pro. Match the plate to the capacity stamped on the magazine, then check that the listing names your pistol too. More on that in the next section.

What does not cross, and why it costs money to get wrong

Barrels. The NDZ Hellcat Pro barrel is a 3.7" OEM-length part in 416R stainless with a 1:10 twist, and its listing carries an explicit line: "Does Not Fit: Hellcat 3", Hellcat RDP Models." The Hellcat barrel is 3", matching the factory length on that gun. These are two different products that happen to sit in the same category. Threaded versions of both exist with a 1/2×28 muzzle thread; setup, thread protectors and comp compatibility are covered in the Hellcat Pro threaded barrel guide.

Recoil springs. NDZ carries ISMI springs for both guns and each listing rules the other one out in writing. The Hellcat spring says it does not fit the Hellcat Pro 3.7". The Hellcat Pro spring says it does not fit the original Hellcat. Both are offered in stock 17 lb, minus 10% and plus 10% weights, so read the model line and not just the spring weight when you order.

Guide rod assemblies. This one is the easiest to get wrong because the listing title names both guns. The NDZ stainless guide rod assembly is a single product page that sells two different parts, and its own feature list says to choose from Hellcat or Hellcat Pro variants to ensure proper fitment. A title that reads "Hellcat & Hellcat Pro" is not the same claim as one part fitting both — check the variant selector before checkout.

Grip sleeves. The Hogue Handall Beavertail sleeve NDZ stocks is described as engineered for the Springfield Armory Hellcat and its product attributes list the gun model as Hellcat, with no mention of the Pro. Given the frames differ by 0.6" in overall length and 0.8" in height, treat Pro fitment as unconfirmed until Hogue or NDZ states it.

Magazine base plates. These follow the magazine and the pistol both. The 15-round base plate is listed for Hellcat, Hellcat Pro and Hellcat Pro Comp and states it does not fit 10 or 13 round magazines. The 10-round plate, HCT9-MP10-V, excludes 11, 13 and 15 round magazines and is listed "For Gun Model: Hellcat" with no mention of the Pro — which matters, because Springfield's low-capacity Pro, HCP9379BOSPLC, ships (2) 10-Round magazines. That owner has no NDZ base plate listed for the magazines the gun came with. Worth knowing too: Springfield sells the Hellcat’s 15-round magazine and the Hellcat Pro’s 15-round magazine under different part numbers — HC5915 and HCP5915 — so buy the plate by the capacity stamped on the magazine you are actually modifying, and confirm the listing names your pistol.

The RDP is a fourth variant, and one listing conflict to watch

Springfield lists the Hellcat RDP as a 3.8" Micro-Compact (HC9389BTOSP), which puts it on the short frame with a longer barrel. That barrel is threaded rather than ported. Springfield's spec sheet gives it as hammer forged steel with a compensator, threaded 1/2×28, in a Melonite finish with a 1:10 twist, and describes the compensator itself as a patented self-indexing design that makes installation or removal easy — a separate muzzle device that comes off, not porting cut into the barrel. It is not the Pro either. Three of the NDZ Hellcat parts that name the RDP are frame parts — the pin kit, the magazine release and the guide rod assembly — which is consistent with the RDP sitting on the short frame. The slide racker plate names the RDP as well, but that one is a slide part: its listing calls it a 2-piece component whose installation "requires that the slide racker plate be screwed to the included rear plate."

The recoil springs are the exception, and there is a contradiction on the shelf. Both ISMI listings name the Hellcat RDP as a fitment while each explicitly excludes the other gun. Both cannot be correct. If you own an RDP, ask NDZ which spring your gun takes before ordering rather than picking one from the listing text. That is a small phone call against the cost of a spring that does not belong in your pistol.

The guide rod assembly carries the same kind of conflict. Its fitment line reads "Designed to fit Springfield Armory Models: Hellcat – 3", Hellcat Pro – 3.7", Hellcat RDP." The only choices it actually offers are the other two, per its own feature list: "Choose from Hellcat or Hellcat Pro variants to ensure proper fitment on your firearm." There is no RDP option to select. The listing names a model it does not sell a variant for, which leaves an RDP owner choosing between two parts specified for other guns. Treat it the way you treat the springs and ask before ordering.

How to shop the category without guessing

Three habits cover almost every fitment mistake on this platform. First, read the "Designed to fit" line on the product page rather than the product title — NDZ writes the model list out on nearly every Hellcat listing, and the title is often broader than the part. Second, when a listing names both guns, check whether it is one part or a variant selector. Third, for anything measured in inches — barrel, recoil spring, guide rod, grip sleeve — assume it is frame-specific until the listing says otherwise. The full Springfield Armory Hellcat parts category carries the current model lines for each part.

Frequently asked questions

Does NDZ make a Hellcat Pro magwell?

A catalog search on September 4, 2026 returned no magwell listed for either the 3" Hellcat or the Hellcat Pro, against 41 results for magwells on other platforms. NDZ does list a magwell for the Springfield Echelon and for the Glock 43X and 48. Check the Hellcat category for current stock, since catalogs change.

Is the Hellcat OSP a different gun from the Hellcat for parts purposes?

No. Every current 3" Hellcat and every current Hellcat Pro that Springfield lists is an OSP model, so OSP describes the optics-ready slide cut rather than a separate frame. Frame parts are unaffected by it; slide parts such as the optic adapter plate and cover plates index to that cut.

Will a Hellcat barrel fit a Hellcat Pro?

No. The Hellcat barrel is 3" and the Hellcat Pro barrel is 3.7". The NDZ Hellcat Pro barrel listing states outright that it does not fit the Hellcat 3" or the Hellcat RDP.

Do the Hellcat and Hellcat Pro use the same recoil spring?

No. The ISMI Hellcat spring states it does not fit the Hellcat Pro 3.7", and the ISMI Hellcat Pro spring states it does not fit the original Hellcat. Both are sold in stock 17 lb, minus 10% and plus 10% weights, so match the model first and the weight second.

Does one optic adapter plate cover both the Hellcat and the Hellcat Pro?

Yes. The NDZ Holosun 407K, 507K and EPS Carry adapter plate is listed as fitting the Hellcat, Hellcat Pro and Hellcat Pro Comp from the same part number, and mounts using the screws supplied with the optic.

Will a Hellcat magazine base plate fit a Hellcat Pro magazine?

Only the 15-round plate. The NDZ 15-round base plate is listed for the Hellcat, Hellcat Pro and Hellcat Pro Comp and states it does not fit 10 or 13 round magazines. The 10-round plate is listed for the Hellcat only, so a Pro shipped with 10-round magazines has no NDZ plate listed. Match the capacity stamped on the magazine, then check that the listing names your pistol.

NDZ Performance is a U.S.-based manufacturer of aftermarket firearm accessories and parts, founded by David Dziob and Antonin Blazek in 2004 and headquartered in Cheshire, Connecticut. Operating a fully equipped in-house CNC shop with 3D printing, CNC milling, lathes, and laser engraving, NDZ produces custom and performance upgrade parts for Glock, Sig Sauer, Smith & Wesson, Springfield Armory, Ruger, CZ, Beretta, Mossberg, Remington, AR-15, AK-47, and more — including guide rods, custom slides, slide cover plates, and magazine base plates. Articles on this blog share product insights, installation guides, and real-world testing to help shooters make informed upgrade decisions.

Leave a Reply