Most owners arrive at the “glock 48 extended magazine” question from the wrong end. They search the phrase, land on one product page, and still do not know whether the magazine sitting in their 43X will run in the 48 next to it. The two pistols share a frame, so the answer is mostly yes — but “mostly” is doing real work in that sentence, and the parts that do not cross over are the ones that get people into trouble. This guide lays out what NDZ Performance actually lists as fitting both guns, what each base plate does to capacity and grip length, and exactly where the shared-parts assumption stops.
Every capacity figure and fitment call below comes from the product listing for that specific part, or from the manufacturer’s own page where one is named. Where neither states something, this page says so instead of guessing.

The short version
- The magazine is shared. The OEM 10-round polymer magazine (SKU GLK-MAG-47818-V) is listed for the G43X and the G48, and its spec block reads “Does Not Fit: G42, G43”. It is no longer the only factory magazine for these pistols — GLOCK announced a 15-round metal SLIMLINE magazine for both in April 2026, and that magazine takes its own base plates.
- The base plates are shared between the pistols, not between the magazines. Every floor plate and capacity extension on this page is listed for both pistols. Nine of the fifteen NDZ plates in the GLK48-MP- line also carry an exclusion naming the G43; the other six carry no exclusion field at all, and scope themselves to the OEM 10-round magazine instead. The four plates in NDZ’s newer GLK43X-MP15 line are for the 15-round metal magazine and read “Does Not Fit: Aftermarket Magazines & 10 Round Magazines”.
- The slide and barrel are not shared. The True Precision X-Fluted barrel is listed for the G48 only; the NDZ43 T.R.O.I. slide is listed for the G43 and G43X.
A workable rule of thumb: from the frame rails down, the 43X and the 48 are the same pistol. Above them, they are not. That is why the magazine, the base plate, the magwell, the grip plug and the guide rod all cross over, while slide-length parts do not.
What changed in 2026: the 15-round metal SLIMLINE magazine
GLOCK announced on April 17, 2026 that “OEM 15-round magazines for the G43X, G48, and G44 models are coming to a GLOCK dealer near you in May 2026,” and that “G43X and G48 SLIMLINE® pistols, chambered in 9×19 mm, will come standard with 15-round GLOCK magazines.” The release is specific about the construction: “The 15-round SLIMLINE magazine has a metal, double stack design.” That shipping date has passed, so a 43X or 48 bought new may not have a 10-round polymer magazine in the box at all.
GLOCK’s own G43X and G48 spec pages still print a standard magazine capacity of 10 as of this writing, so its site carries both figures. Which magazine came with your pistol decides which plate you can buy, and it belongs up front: plates for the OEM 10-round polymer magazine and plates for the 15-round metal magazine are separate parts. That is not an inference. On the metal side, all four NDZ plates for the 15-round magazine publish the same fitment line: “Designed to fit Glock Models: 43X 48 – 15 Round Metal Magazines. Does Not Fit: Aftermarket Magazines & 10 Round Magazines.” On the polymer side, Ghost puts it in the product name — both of its extensions carry “NOT FOR METAL MAGS” in the title, and the +4 description reads “Adds four rounds for your GLOCK 43X & 48 OEM 9mm magazines – Not for metal mags !” NDZ’s extended plate is scoped the same way, publishing its fitment as “43X & 48 OEM 10 Round Mags ONLY”.
Six NDZ plates answer that question in their own fitment line rather than leaving it open. The extended plate quoted above and five siblings — GLK48-MPX-V, GLK48-MPX-AT-V, GLK48-MPX-BRS-V, GLK48-MPX-BRS-AT-V, GLK48-MP-BRS-V and GLK48-MP-BRS-AT-V — publish no model exclusion at all, and their only fitment field scopes them to the OEM 10-round magazine, which is also a statement that they are not listed for the metal one. The other nine plates in the GLK48-MP- line name pistols rather than magazines and say nothing about magazine type in either direction, and Ghost’s exclusion says its two extensions do not fit metal magazines. If the magazine in your hand is the metal one, do not assume any of those plates fits it: no plate in the GLK48-MP- line names the metal magazine in its fitment. Buy from the four plates NDZ lists for the 15-round metal magazine instead, covered in their own section below.
Glock 48 and 43X magazine and base plate chart
Every row below is a factory magazine with a different plate on the bottom of it: the OEM 10-round polymer magazine first, then the 15-round metal magazine. Capacities are taken from the individual product listings. Where a listing states a “+2” or “+4” without naming a total, the total shown assumes you started with the OEM 10-round polymer magazine — that is arithmetic on two sourced numbers, not a figure printed anywhere. Where a listing says nothing about capacity, the cell reads Not confirmed.
| Magazine | Base plate option | Capacity | Fits Glock 48 | Fits Glock 43X | NDZ part |
|---|---|---|---|---|---|
| Glock OEM 10-round polymer 9mm | Factory polymer plate, as shipped | 10 | Yes | Yes | GLK-MAG-47818-V |
| Glock OEM 10-round polymer 9mm | NDZ aluminum magazine floor base plate | 10 — no change | Yes | Yes | GLK48-MP-V |
| Glock OEM 10-round polymer 9mm | NDZ floor plate with finger extension | 10 — no change | Yes | Yes | GLK48-MPF-V |
| Glock OEM 10-round polymer 9mm | Pearce Grip finger grip extension | 10 — no change | Yes | Yes | PG-48 |
| Glock OEM 10-round polymer 9mm | NDZ extended / extra-thick brass base plate | Not confirmed | Yes | Yes | GLK48-MPX-V, GLK48-MPX-BRS-3D-V |
| Glock OEM 10-round polymer 9mm | NDZ Plus 2 magazine extension | 12 (+2) | Yes | Yes | GLK48-MP2-V |
| Glock OEM 10-round polymer 9mm | Ghost Plus 2 M.E.D., spring included | 12 (+2) | Yes | Yes | GHO-MED-48PLUS2 |
| Glock OEM 10-round polymer 9mm | Ghost Plus 4 extension, spring included | 14 (+4) | Yes | Yes | GHO-MED-48PLUS4 |
| Glock OEM 15-round metal SLIMLINE 9mm | Factory plate, as shipped | 15 | Yes | Yes | — |
| Glock OEM 15-round metal SLIMLINE 9mm | NDZ aluminum magazine base plate, standard or Aspis cut | 15 — no change | Yes | Yes | GLK43X-MP15-V, GLK43X-MP15-AT-V |
| Glock OEM 15-round metal SLIMLINE 9mm | NDZ aluminum extended magazine base plate, standard or Aspis cut | 15 — no change | Yes | Yes | GLK43X-MPX15-V, GLK43X-MPX15-AT-V |
| Glock OEM 6-round 9mm (G43) | Factory polymer plate | 6 | Listed for G43 only | Listed for G43 only | GLK-MAG-43006-V |
Two rows deserve a note. The Not confirmed row covers the NDZ extended and extra-thick brass plates: both are listed for the G43X and G48 and both replace the factory floor plate, but neither listing states whether the plate changes round count, so this page will not put a number in that cell. And the G43 row is there because it is the single most common mix-up — the 6-round magazine that came with a Glock 43 is a different part from the 10-round magazine that came with a 43X or a 48.
What a base plate actually changes
A magazine floor plate can change three things: the material and weight at the bottom of the magazine, the amount of grip length below your hand, and the number of rounds the magazine holds. Most plates change one or two of the three, and the marketing rarely separates them. Reading the listing for which of the three it changes is the whole skill.
Plates that add grip, not rounds
The NDZ aluminum floor base plate (GLK48-MP-V) is machined from 6061 T6 billet aluminum and mil-spec anodized. Its listing is explicit: these plates do not alter the capacity of the magazine, they replace the stock floor plate, and all other factory components stay in place. What you get is a small amount of extra grip length and a textured front face that guides the lower finger into position.
The NDZ finger extension plate (GLK48-MPF-V) is the same idea with more of it — additional textured length with tactical ridges, and the same statement that capacity is unchanged. Its spec block carries the same exclusion as the aluminum plate, “Does Not Fit: G42, G43”. Neither NDZ plate publishes an added-length figure.
The Pearce Grip PG-48 is the third option in this group, and it is the one with a number attached — but the number depends on whose page you read. Pearce Grip’s own product page reads: “This extension replaces the magazine floor plate adding approximately 5/8" additional length resulting in better control and comfort without altering the capacity of the factory magazine.” Five-eighths of an inch is 0.625 in. The NDZ listing for the same part instead says the PG-48 gives you “about 0.75" of extra finger length”. Take 5/8 in as the manufacturer’s figure and 0.75 in as the reseller’s. Both pages agree that capacity does not change. Only the NDZ listing goes further, its feature list reading “No capacity change, direct replacement that retains all factory internals and follower.” Pearce’s page does not mention the internals or the follower at all.
The PG-48 is not the only part here with a published dimension. Ghost prints three figures on both of its extension pages — 4.30 for the OEM magazine, 4.76 with the +2 and 5.24 with the +4, each carrying an inch mark — without labelling which dimension they measure. The differences are 0.46 in for the Ghost +2 and 0.94 in for the +4.
This is the category most 48 and 43X owners actually want. The slimline frame is narrow and short, and for anyone with average or larger hands the pinky simply has nowhere to go. A grip-only plate fixes that without touching the magazine’s internals, which means nothing about the feeding cycle changes.
Plates that add rounds
The NDZ Plus 2 magazine extension (GLK48-MP2-V) adds two rounds, taking an OEM 10-round polymer magazine to 12. It is listed for the G43X and G48 only and states plainly that it does not fit the Glock 43. It replaces the stock floor plate and retains the factory insert and spring — and the listing itself recommends an extra-power magazine spring to handle the additional travel.
The Ghost Plus 2 Magazine Extension Device (GHO-MED-48PLUS2) also adds two rounds and takes the spring problem off your plate by shipping a stainless steel plus-power spring in the box, alongside an integrated pinky rest. The Ghost Plus 4 (GHO-MED-48PLUS4) is the largest jump listed for these magazines: four extra rounds, so 14 from an OEM 10-round polymer magazine, again with a stainless replacement spring included and the original follower and internals retained. Ghost’s own pages add an exclusion the NDZ listings do not repeat — “Does not work on the 42 or 43” — alongside the metal-magazine exclusion above.
Notice the pattern. Every listing that adds rounds also talks about the spring. That is not upselling.
Why the spring is not optional
When an extension lengthens the magazine body, the follower has farther to travel and the same factory spring has to keep presenting rounds all the way to the top of that longer stack. A spring that was adequate for ten rounds is being asked to do more work over more distance. The symptoms of getting this wrong are the ones the ISMI spring listing names: it sells the part as fixing “failures-to-feed and stovepipes” caused by a fatigued spring. No listing here states where in the magazine those show up.
The ISMI plus-10% magazine spring (ISMI-MS-G48PLUS2) exists for exactly this job. It is listed for the G43X and G48, explicitly not for the G43, and its listing describes it as compensating for extended base plates so the follower fully presents rounds, as well as replacing fatigued springs that cause weak-feed symptoms. If you buy a capacity plate that does not include a spring, budget for one in the same order. If you buy a Ghost extension kit, the spring is already there.
There is more than one standalone spring for these magazines, and they are not interchangeable. NDZ sells the ISMI part under the manufacturer SKU G48+2, and ISMI’s own page scopes it to “Glock 48 magazines with a +2 extension” — it is a +2 spring, not a general-purpose one. NDZ also lists two Ghost magazine springs sold on their own: GHO-MS-48P2, whose listing reads “Compatible with NDZ Performance +2 base plates”, and GHO-MS-48P4, whose listing states “Not compatible with NDZ Performance extension plates” and adds that it “is intended for use with Ghost-compatible +4 extensions only”. Match the spring to the extension you actually installed.
Plates for the 15-round metal magazine
NDZ lists four aluminum plates for GLOCK’s 15-round metal SLIMLINE magazine: a standard base plate (GLK43X-MP15-V), an extended base plate (GLK43X-MPX15-V), and an Aspis-cut version of each (GLK43X-MP15-AT-V and GLK43X-MPX15-AT-V). All four are listed for the 43X and the 48, and all four carry the same exclusion: “Does Not Fit: Aftermarket Magazines & 10 Round Magazines.” Read that line in both directions. These plates are not for the 10-round polymer magazine, and none of the fifteen plates in the GLK48-MP- line names the metal one.
None of the four adds rounds. Each listing answers its own capacity question the same way: “Does this change my magazine capacity? No. It replaces the factory base plate and retains the magazine’s capacity and all other factory components.” What they change is the bottom of the magazine — the listings say “The added weight of an all-metal plate helps magazines eject smoothly and consistently when swapping mags.” The two extended plates do not publish an added-length figure, so this page does not give one. All four sit in the same 43X and 48 magazine extensions category as the polymer-magazine plates, so check the magazine named in the title before you add one to the cart.
What else crosses between the 48 and the 43X
| Part | Fitment as listed | Crosses 43X ↔ 48? | Example SKU |
|---|---|---|---|
| OEM 10-round magazine | G43X, G48 — does not fit G42, G43 | Yes | GLK-MAG-47818-V |
| Magazine base plates and extensions, 10-round polymer magazine | G43X, G48 — the “Does Not Fit: G42, G43” field is on eight of the fifteen NDZ plates; one more names the G43 in its description only, six carry no exclusion, and the Pearce and Ghost plates carry none | Yes | GLK48-MP-V, GLK48-MPF-V |
| Magazine base plates, 15-round metal magazine | 43X, 48 15-round metal magazines — does not fit aftermarket magazines or 10-round magazines | Yes | GLK43X-MP15-V, GLK43X-MPX15-V |
| Extra-power magazine spring | G43X, G48 — does not fit G43 | Yes | ISMI-MS-G48PLUS2 |
| Magwell | G48, G43X — does not fit all other models | Yes | GLK43X-MW-V1-V |
| Grip plug | G43X, G48 | Yes | GLK43X-GP-V |
| Guide rod assembly | G43, G43X, G48 | Yes — and the G43 too | NDZ-GRA-G43-SW-V |
| Extended slide lock lever | G48, G43, G43X — does not fit Gen 1-5 models, G42 | Yes | NDZ-ESLL-48-V |
| Drop-in trigger | G43, G43X, G48 — does not fit Gen 1-5, G42 | Yes | TP-G43T-BLBL |
| Barrel, non-threaded | G48 | No — listed for the G48 only | TP-G48B-X-V |
| Aftermarket slide | G43, G43X | No — not listed for the G48 | NDZ-SLD-GLK43-V1-PAT7-RP |
Two of these are worth a sentence each. The NDZ magwell (GLK43X-MW-V1-V) is a single part listed for the G48 and G43X and nothing else, and its listing puts a number on the weight it adds: 0.85 oz. The NDZ guide rod assembly (NDZ-GRA-G43-SW-V) reaches one model further, covering the G43, G43X and G48 in one part, and adds 0.67 oz to the front of the pistol; if you are weighing that upgrade, the reasoning is broken down in our post on whether a Glock 43X guide rod needs to be steel.
If you want to see the full slimline parts line in one place rather than SKU by SKU, the G43X and G48 parts category is the index, and the 43X and 48 magazine extensions category holds the plates and extensions discussed above, for both the polymer and the metal magazine.
Check the SKU, not the listing title
The most reliable habit when buying for either of these pistols is to read the manufacturer SKU and the fitment field, not the product name. The Glock 43 shows why.
NDZ makes no magazine base plate for the Glock 43 at all — the Glock 43 plates it carries are other companies’ parts, Ghost’s GHO-MED-43 and Pearce’s PG-43 and PG-43-1. NDZ’s standalone 43X and 48 plates sit in two SKU lines: the older GLK48-MP- line, and GLK43X-MP15 for the 15-round metal magazine. Of the fifteen plates in the GLK48-MP- line, eight carry an explicit “Does Not Fit: G42, G43” field in the spec block; GLK48-MP2-V carries no such field and names only “Does Not Fit: Glock G43.” in its description; and six publish no exclusion field at all, scoping themselves to the OEM 10-round magazine instead. A Glock 43 plate and a 43X/48 plate look broadly similar in photographs, and where a listing addresses that difference it addresses it in a field most people scroll past. Where it does not, silence is not permission. For the wider picture across the whole Glock line, our guide to Glock magazine compatibility by model and caliber covers the rest of the family.
Buying order that avoids rework
If the goal is grip only, buy the plate and stop — nothing internal changes, so nothing else needs to change with it. If the goal is capacity, treat the plate and the spring as one purchase, and confirm whether your chosen extension already includes a spring before you add a second one to the cart. And if you own both a 43X and a 48, buy once: an OEM 10-round polymer slimline magazine and the plates that fit it will serve both pistols, which is the practical payoff of the shared frame.
Frequently asked questions
Do Glock 43X magazines fit the Glock 48?
Yes. The OEM 10-round polymer 9mm magazine, SKU GLK-MAG-47818-V, is listed for both the G43X and the G48, and its spec block reads “Does Not Fit: G42, G43”. GLOCK announced in April 2026 that both pistols would also come standard with a 15-round metal SLIMLINE magazine from May 2026. Base plates do not cross between those two magazines.
Do 10-round base plates fit the 15-round metal magazine?
Not on the strength of any listing. No plate in NDZ’s GLK48-MP- line names the metal magazine in its fitment: six read “OEM 10 Round Mags ONLY” and nine name only the pistols. NDZ lists four separate plates for the 15-round metal magazine — GLK43X-MP15-V, GLK43X-MPX15-V and an Aspis-cut version of each — and all four read “Does Not Fit: Aftermarket Magazines & 10 Round Magazines”. None of the four changes capacity, according to its listing.
Will a Glock 43 magazine work in a Glock 48?
Treat them as separate magazines. The OEM 6-round magazine, GLK-MAG-43006-V, is listed for the Glock 43 only, and the 10-round 43X/48 magazine is listed as not fitting the G43. Eight of the fifteen NDZ base plates in the GLK48-MP- line carry an explicit “Does Not Fit: G42, G43” field, which rules out the G42 as well; GLK48-MP2-V names only the G43, in its description; and six carry no exclusion field at all, so it is not every plate. None of the listings we checked states what happens in the reverse direction, so this page will not claim one.
How many rounds does a Glock 48 hold with an extension?
From the OEM 10-round polymer magazine: 12 with a +2 extension such as the NDZ Plus 2 (GLK48-MP2-V) or the Ghost Plus 2 M.E.D., and 14 with the Ghost Plus 4. Grip-only plates including the NDZ finger extension plate and the Pearce PG-48 leave capacity at 10. The 15-round metal magazine stays at 15 with any of the four NDZ plates listed for it.
Do I need a new magazine spring with a +2 or +4 extension?
Plan on it. The NDZ Plus 2 listing recommends an extra-power spring for the increased travel of the rounds, and both Ghost extension kits include a stainless plus-power spring for the same reason. Standalone springs are sold as well, and they are extension-specific. ISMI scopes its G48+2 spring, which NDZ lists as ISMI-MS-G48PLUS2, to “Glock 48 magazines with a +2 extension”. The Ghost GHO-MS-48P2 listing reads “Compatible with NDZ Performance +2 base plates”. The Ghost GHO-MS-48P4 listing states “Not compatible with NDZ Performance extension plates” and is for Ghost +4 extensions only. Match the spring to the extension you installed.
Is the Glock 48 magwell the same part as the 43X magwell?
Yes. Each NDZ magwell for these pistols is one part for both: GLK43X-MW-V1-V is listed for the G48 and G43X, with a fitment field stating it does not fit any other model, and adds 0.85 oz. The low-profile magwell, GLK43X-LPMW-V, is also listed for the G43X and G48.
Does the Glock 48 slide fit a 43X?
Slide and barrel parts are listed per model, not as a 43X/48 pair. The True Precision X-Fluted barrel is listed for the Glock 48 only, and the NDZ43 T.R.O.I. slide is listed for the Glock 43 and 43X. Shared fitment on this platform is a frame-side property, not a whole-pistol one.
