Glock 43X MOS Slide: Optic Footprints, Sight Height and Glock 48 Fit

18 min read

If you are shopping for a Glock 43X MOS slide — or trying to work out what will actually bolt to the one already on your pistol — the deciding question is which footprint the factory cut accepts, which screws it takes, and whether the irons you have will still be usable with an optic sitting above them. GLOCK answers the first two itself, on its Optic Mounting page rather than on the pistol’s product listing, and the answer depends on which of two Slimline cuts your gun left the factory with. This guide follows what GLOCK, Shield Sights, Holosun, Trijicon and the NDZ catalogue publish in writing, and says not confirmed everywhere they do not. On a firearm, a guessed fitment is worse than an open question.

NDZ43 T.R.O.I. slide in Blackout and Tungsten US Flag Cerakote, shown for the slimline slide and optic footprint guide.

What GLOCK actually publishes about the Slimline MOS cut

The G43X MOS product page describes the slide without naming a footprint: the pistol “features slide cuts designed for specific micro-optics and the GLOCK Slim Mounting Rail for mounting accessories.” Directly under that description sits a second note: “The G43X with the Modular Optic System (MOS) does not come with adapter plates.” The G48 MOS page carries the same note under its own model name: “The G48 with the Modular Optic System (MOS) does not come with adapter plates.”

Plenty of buying guides stop there and conclude that the factory never says what fits. It does — one level up, on GLOCK’s Optic Mounting page, where the Slimline system gets its own section. “The Slimline MOS pistol models have slide cuts designed for specific micro-optics and do not need Adapter Plates,” GLOCK writes, and then names the pattern outright: “The standard SLIMLINE MOS cut fits the Shield RMSc footprint and uses M4 screws.” That is the footprint and the thread, from the manufacturer, in one sentence. It is also why nothing ships in the box to adapt the cut: there is no plate to fit, because the slide is milled to the optic.

GLOCK’s launch release for these two pistols says the same thing in different words: “With a non-standard MOS footprint, the Slimline MOS models require specific mico-reflex optics such as the Shield RMSc.” (The typo is GLOCK’s.) Read that as the warning it is. A Slimline MOS slide is not a scaled-down full-size MOS slide, and the RMR-pattern optics and stacked adapter plates that populate the full-size MOS system are not part of this one.

Standard MOS or MOS-K? Check the item number first

There is a second Slimline cut, and it changes the answer. GLOCK: “Some SLIMLINE models will instead feature the MOS-K cut. The Slimline MOS-K is modified to accept either Holosun K or RMSc footprints without the need for adapter plates.”

So the standard cut takes a Shield RMSc; the MOS-K cut takes a Shield RMSc or a Holosun K. Neither takes an adapter plate. That single distinction decides which optics belong on your shopping list, and it is not something you can settle by reading the model name on the box — both are sold as MOS. GLOCK publishes the identification method instead: “You can identify which cut your pistol has by referencing the pictures or by checking the item number sticker on the handle of your pistol case. The standard cut will have “MOS” and the MOS-K cut will include “MOSK” near the end of the item number.”

Photographs of both cuts sit next to that text on the same GLOCK page, so a side-by-side comparison is available even if the case sticker is long gone. What is not available is a published list of which G43X and G48 item numbers carry which cut — GLOCK gives you the method, not the roster. Identify the gun in front of you rather than reasoning from a model name.

Optic footprints and the 43X MOS cut

Every “fits the cut” cell below is answered from a manufacturer’s own published wording, not from a compatibility chart on a forum. Where nobody publishes it, the cell says so.

Optic footprintFits the 43X MOS cut?Adapter plate needed?NDZ part
SHIELD footprint (Shield RMSc)Yes — GLOCK names it. “The standard SLIMLINE MOS cut fits the Shield RMSc footprint and uses M4 screws,” and the MOS-K cut “is modified to accept either Holosun K or RMSc footprints without the need for adapter plates.” Shield’s own page describes the RMSc as “designed to fit on single-stack pistols such as concealed carry handguns like the Glock 43, Smith & Wesson Shield, and the 1911,” adding that “the latest addition to the arsenal is the Glock 43x and G48.”No. GLOCK: Slimline MOS models “have slide cuts designed for specific micro-optics and do not need Adapter Plates.” None ship in the box, and none are wanted.The NDZ43 T.R.O.I. slide is milled with a “Red dot optic cut with Shield RMSC footprint” — an aftermarket slide, not the factory MOS slide.
Holosun K footprint (HS407K-X2, HS507K-X2)On the MOS-K cut only. GLOCK states the “Slimline MOS-K is modified to accept either Holosun K or RMSc footprints without the need for adapter plates,” and names the RMSc alone for the standard cut. Holosun’s own pages name no host pistol and word the footprint differently: the HS507K-X2 lists “Direct Mount” and “K Footprint”, the HS407K-X2 “Direct Mount” and “Holosun K Footprint”.No, on a MOS-K cut — GLOCK says “without the need for adapter plates.” Holosun’s KPLT-MOS9MM plate “Allows Holosun 407K and 507K series optics to mount securely to Glock MOS 9mm optics-ready pistol slides,” but that page never separates a Slimline cut from a full-size one and never names the 43X.None confirmed for the 43X in the NDZ catalogue.
RMR footprint (e.g. Holosun HS507C-X2)Not among the footprints GLOCK names, and the size is against it. GLOCK names the Shield RMSc for the standard cut and Holosun K or RMSc for the MOS-K cut; the RMR pattern appears in neither. Holosun lists this optic’s body at 1.15 in wide; GLOCK lists the 43X MOS slide at 0.87 in wide, so the optic is 0.28 in wider than the slide it would sit on.GLOCK publishes no Slimline adapter plate at all, and states the cuts do not need one.None confirmed for the 43X.
Trijicon RMRccNot among the footprints GLOCK names, and Trijicon says why. Its RMRcc page publishes a full spec block — body 1.8 in x .95 in x .97 in, Mount “Not included”, two #5-40 UNC x .25 in socket-head cap screws in the box — and a note that “The RMR®cc has a unique footprint in order to pack all the RMR features in a compact package while maintaining the legendary durability for which Trijicon is best known.” A unique footprint is, on Trijicon’s own description, neither the RMSc nor the Holosun K.Not confirmed for a Slimline MOS cut.None confirmed for the 43X.
Sources: GLOCK Optic Mounting page; GLOCK G43X MOS and G48 MOS product pages; GLOCK Slimline MOS press release; Shield Sights RMSc product page; Holosun HS407K-X2, HS507K-X2, HS507C-X2 and KPLT-MOS9MM product pages; Trijicon RMRcc product page; NDZ product listings. Retrieved 9 September 2026.

One naming trap survives all of that. Holosun calls the 407K/507K pattern its “K footprint.” Shield calls its own pattern “the SHIELD footprint.” Retailers, NDZ included, routinely file the Holosun K-series under “RMSC” — NDZ’s adapter plate for a different pistol is literally titled Holosun 407K 507K RMSC Adapter Plate. GLOCK’s MOS-K sentence closes the practical half of that question for one cut and one cut only: that cut “is modified to accept either Holosun K or RMSc footprints.” Read it for exactly what it says. It is GLOCK describing a slide it milled to take both patterns — not a statement that the two footprints are dimensionally identical, and not a claim about any other slide, plate or pistol. On a standard SLIMLINE MOS cut, GLOCK names the RMSc alone.

Screws are the second fitment problem

A matching bolt pattern still fails if the threads are wrong. GLOCK publishes a thread for each Slimline cut, and they are not the same:

  • Standard SLIMLINE MOS cut — GLOCK: it “fits the Shield RMSc footprint and uses M4 screws.”
  • Slimline MOS-K cut — GLOCK: “Optics should be mounted using the M3 screws provided by optics manufacturers.” The same paragraph carries a warning worth reading twice: “The optic cover plate screws provided are specifically for the optic cover plate and are not to be used with the optic.”

The optics line up with that, which is confirmation rather than coincidence:

  • Shield RMSc ships with 2x M4x8 mm and 2x M4x10 mm button-head screws — M4, exactly what GLOCK specifies for the standard cut — and Shield sells an Imperial #6-32 x 3/8 in set separately for optics-ready guns that need it.
  • Holosun HS507K-X2 ships with 2x M3x12 and 2x M4x12 screws, covering both threads out of the box.
  • The NDZ43 T.R.O.I. slide lists its optic thread size as 6-32 — an imperial thread, and a reminder that an aftermarket slide sets its own spec regardless of what the factory cut uses.

Two factory cuts, two metric threads, and an aftermarket slide on an imperial one. Establish which cut you own before you order hardware, mount the optic with the screws its maker supplied rather than the cover-plate screws GLOCK ships with the pistol, and stop if a fastener does not start by hand. Cross-threading an optic screw into a slide is not a mistake you fix with a longer screw.

What an optic changes about sight height

This is where honest sourcing costs you a tidy answer. The published optic body heights are: Shield RMSc 0.89 in, Holosun HS407K-X2 and HS507K-X2 0.95 in, Holosun HS507C-X2 1.15 in. Those numbers are total body height, not height above the slide — part of the optic drops into the milled pocket. They do not tell you where the dot window lands relative to your irons, because that depends on how deep the cut is milled, and GLOCK publishes no cut depth for either Slimline cut.

GLOCK does state an intent for the system, in the launch release for these two pistols: the slim design “eliminates the need for high, back-up sights by allowing visibility of the standard GLOCK sights through the lens of the compact optic.” That is the factory telling you standard-height irons are meant to be visible through the window — not a measured co-witness figure for any particular optic on any particular gun. Treat it as the starting expectation, then confirm it with your optic actually mounted.

Shield makes a co-witness claim of its own, and it is worth quoting precisely rather than paraphrasing: “When coupled with our matching low-profile Glock MOS plate, the RMS sits so low that the sight will co-witness without the need for suppressor sights.” Note the two conditions in that sentence. It is the RMS, and it assumes Shield’s own GLOCK MOS plate — hardware a Slimline cut neither needs nor uses.

GLOCK does at least confirm that sight choice is a dimensional change on this pistol. Its G43X MOS specification lists three different “Line of Sight” figures depending on what is installed — 5.24 in with polymer sights, 5.20 in with steel, 5.16 in with GLOCK night sights. That is a 0.08 in spread from the sights alone.

One iron sight set needs a warning here rather than a recommendation. The Trijicon HD 3-dot night sight set for GLOCK small frames, SKU GL113-C-600785, is listed by Trijicon as “Fits Glock Model: 42, 43, 43x, 43E, and 48 (excluding MOS models).” The pistol this guide is about is an MOS model. Trijicon excludes it. Do not order that set for a 43X MOS. The NDZ listing now prints the same exclusion in its fitment line — Does Not Fit: MOS models — and Trijicon’s own page is where it comes from.

Trijicon does publish the sight dimensions the retail listing leaves out. For the same SKU it lists Overall Front Blade Height 0.268 in (6.8 mm) and Overall Rear Height 0.291 in (7.39 mm), with a front blade 0.215 in tall and 0.144 in wide and a rear blade 0.201 in tall behind a 0.169 in U-notch. GLOCK’s own OEM listings publish no height. So the numbers exist, but they belong to a set the maker excludes from MOS guns, and GLOCK still publishes no optic cut depth — which means co-witness height on a 43X MOS is not a calculation you can close from catalogue data. Measure your own gun, or fit and look.

What an optic changes about slide choice

If you own a non-MOS 43X, or you want a footprint neither factory cut accepts, the answer is a different slide rather than a plate. The NDZ category for Glock 43 and 43X slides currently holds eight slides across the A.R.E.S., Achilles, Artemis, Cerberus, T.R.O.I. and blank models, every one of them filed under gun models G43 and G43X.

Several of them publish an optic specification, and they agree on the footprint. The NDZ43 T.R.O.I. slide is billet stainless with precision-cut serrations, porting on the top and sides for weight reduction and ported barrels, a “Red dot optic cut with Shield RMSC footprint” and an “Optic Thread Size: 6-32”. The black-nitride T.R.O.I. listing (NDZ-SLD-G43-TROI-BN) publishes the same 6-32 optic thread and describes “an optic cut designed to accept red dot sights with a shield RMSC footprint”. The Artemis slide and barrel kit (NDZ-SLD-G43-ART-RMSC-V) describes “an optic-ready RMSC cut” but publishes no optic thread size. Choosing a slide by its milled footprint removes the plate question entirely, which on a Slimline gun is the whole point — there is no factory plate to lose, strip or shim.

Barrel choice rides along with slide choice. NDZ’s match-grade 43X barrel is listed for the G43 and G43X at 3.41 in non-threaded, or 3.9 in with a 1/2 x 28 thread, in 416R stainless with 1:10 broach-cut rifling. That 3.41 in figure is exactly the barrel length GLOCK publishes for the G43X MOS — which brings us to the question that trips up more buyers than any footprint does.

Does a Glock 43X slide run on a Glock 48?

The two pistols share a frame footprint and differ entirely in the slide assembly. Every number below is from GLOCK’s own specification tables for the two MOS models.

Published dimensionG43X MOSG48 MOS
Barrel length3.41 in (87 mm)4.17 in (106 mm)
Slide length6.06 in (154 mm)6.85 in (174 mm)
Overall length6.50 in (165 mm)7.28 in (185 mm)
Line of sight (steel sights)5.20 in (132 mm)5.94 in (151 mm)
Weight without magazine16.26 oz (461 g)18.31 oz (519 g)
Slide width0.87 in (22 mm)0.87 in (22 mm)
Overall width1.10 in (28 mm)1.10 in (28 mm)
Height including magazine5.04 in (128 mm)5.04 in (128 mm)
Trigger distance2.64 in (67 mm)2.64 in (67 mm)
Standard magazine capacity1010
Source: GLOCK G43X MOS and G48 MOS technical data, retrieved 9 September 2026.

The pattern is clean. Everything the frame governs — height, overall width, trigger distance, magazine capacity — is identical to the published figure. Almost everything the slide governs differs: 0.79 in of slide length, 0.76 in of barrel, 0.74 in of sight line, and just over 2 oz. The one slide dimension that matches is width, which GLOCK publishes as 0.87 in on both pistols. That is why an optic sized against the 43X slide is sized against the G48 slide too.

That is why the parts market splits the way it does. Magazines, magazine plates, magwells, triggers, extractors, guide rods and rear slide plates are commonly listed for “43X 48” together. Slides and barrels are not: NDZ’s 43X barrel is listed for the G43 and G43X only, and the True Precision X-Fluted barrel for the Glock 48 is listed for the G48 only. Two different part numbers, because they are two different lengths.

So can you physically run a 43X slide assembly on a 48 frame? We could not source an answer, and we are not going to invent one. GLOCK publishes no cross-model slide compatibility statement on either MOS page, and every aftermarket slide we checked is listed for the G43 and G43X, never the G48. Read a store category name as a merchandising grouping, not a fitment guarantee. The safe rule is the boring one: buy the slide and barrel for the model printed on the part, and if you want a definitive cross-model answer, put it to a gunsmith with both guns on the bench.

For the wider picture on which GLOCK slides interchange across generations and frame sizes, see our Glock slide compatibility guide. If you are cross-shopping the platform against a SIG, the Glock 43X and P365 slide upgrade guide covers that comparison.

What we could not confirm

Publishing the gaps is more useful than papering over them, so here they are in full:

  • GLOCK names the footprints on its Optic Mounting page but publishes no roster of which G43X and G48 item numbers carry the standard cut and which carry MOS-K. You get the identification method, not a lookup table.
  • Neither Holosun K-series product page mentions GLOCK, the 43X or the Slimline family at all. The MOS-K fitment statement comes from GLOCK, not from Holosun.
  • No manufacturer document states that the Holosun K footprint and the Shield RMSc footprint are dimensionally identical. GLOCK states only that its MOS-K cut accepts either, which is a fact about that cut and not about the two patterns in general.
  • No optic cut depth is published for either Slimline cut. Trijicon does publish blade heights for its GL113 HD night sight set — 0.268 in overall front, 0.291 in overall rear — but that set is excluded from MOS models, so co-witness on this pistol still cannot be calculated from catalogue data.
  • No cross-model slide compatibility statement exists between the G43X and the G48 from either GLOCK or the aftermarket listings we read.

If you need a definitive answer for a specific optic on a specific gun, identify your cut first and then call the optic manufacturer with the pistol in hand. On a firearm, “probably fits” is not a specification.

Frequently asked questions

Does the Glock 43X MOS come with optic adapter plates?

No, and it does not need them. GLOCK prints the note directly on the G43X MOS product page: “The G43X with the Modular Optic System (MOS) does not come with adapter plates.” The G48 MOS page carries the same note under its own model name: “The G48 with the Modular Optic System (MOS) does not come with adapter plates.” GLOCK’s Optic Mounting page explains why: “The Slimline MOS pistol models have slide cuts designed for specific micro-optics and do not need Adapter Plates.” The optic bolts straight to the milled cut.

Which optic footprint does the Glock 43X MOS slide use?

GLOCK publishes the answer on its Optic Mounting page, and it depends on which of two Slimline cuts your pistol has. “The standard SLIMLINE MOS cut fits the Shield RMSc footprint and uses M4 screws.” The second cut is broader: “Some SLIMLINE models will instead feature the MOS-K cut. The Slimline MOS-K is modified to accept either Holosun K or RMSc footprints without the need for adapter plates.” The G43X MOS product page itself names no footprint — it says only that the pistol “features slide cuts designed for specific micro-optics and the GLOCK Slim Mounting Rail for mounting accessories” — so use the Optic Mounting page, not the product listing.

How do I tell whether my 43X MOS has the standard cut or the MOS-K cut?

GLOCK gives two ways. “You can identify which cut your pistol has by referencing the pictures or by checking the item number sticker on the handle of your pistol case. The standard cut will have “MOS” and the MOS-K cut will include “MOSK” near the end of the item number.” Photographs of both cuts appear alongside that text on GLOCK’s Optic Mounting page. GLOCK does not publish a list of which model numbers carry which cut, so identify the pistol in front of you rather than reasoning from the model name.

Will a Glock 43X slide fit a Glock 48?

Not confirmed, and the published dimensions differ substantially. GLOCK lists the G43X MOS slide at 6.06 in with a 3.41 in barrel, and the G48 MOS slide at 6.85 in with a 4.17 in barrel. Frame-side figures such as height, width and trigger distance are identical between the two, which is why frame parts are cross-listed and slides and barrels are not.

Do I need taller iron sights after mounting a red dot on a 43X MOS?

GLOCK’s stated intent is that you do not. Its launch release for the Slimline MOS models says the slim design “eliminates the need for high, back-up sights by allowing visibility of the standard GLOCK sights through the lens of the compact optic.” That is a design claim about the system, not a measured figure for your optic: GLOCK publishes no optic cut depth for either Slimline cut, so the exact relationship between the dot window and your irons cannot be calculated from catalogue data. Note also that Trijicon’s GL113 HD night sight set — Overall Front Blade Height 0.268 in, Overall Rear Height 0.291 in — is listed as fitting “42, 43, 43x, 43E, and 48 (excluding MOS models)”, so it is not a set for this pistol. Fit the optic and check your sight picture before ordering anything taller.

What screws does a micro red dot use on a Glock 43X MOS slide?

GLOCK specifies a thread for each cut. The standard SLIMLINE MOS cut “fits the Shield RMSc footprint and uses M4 screws.” On the MOS-K cut, “Optics should be mounted using the M3 screws provided by optics manufacturers,” and GLOCK warns that “The optic cover plate screws provided are specifically for the optic cover plate and are not to be used with the optic.” The optics match: Shield ships the RMSc with M4x8 mm and M4x10 mm screws and sells a #6-32 x 3/8 in set separately, and Holosun ships the HS507K-X2 with both M3x12 and M4x12. The aftermarket NDZ43 T.R.O.I. slide is the exception — it lists a 6-32 imperial optic thread, because an aftermarket slide sets its own spec.

NDZ Performance is a U.S.-based manufacturer of aftermarket firearm accessories and parts, founded by David Dziob and Antonin Blazek in 2004 and headquartered in Cheshire, Connecticut. Operating a fully equipped in-house CNC shop with 3D printing, CNC milling, lathes, and laser engraving, NDZ produces custom and performance upgrade parts for Glock, Sig Sauer, Smith & Wesson, Springfield Armory, Ruger, CZ, Beretta, Mossberg, Remington, AR-15, AK-47, and more — including guide rods, custom slides, slide cover plates, and magazine base plates. Articles on this blog share product insights, installation guides, and real-world testing to help shooters make informed upgrade decisions.

Leave a Reply